View LT1964_323193.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Final Electrical Specifications
LT1964 200mA, Low Noise, Low Dropout Negative Micropower Regulator in ThinSOT
October 2001
FEATURES
s s s s s s s s s s s
DESCRIPTIO
s
Low Profile (1mm) ThinSOTTM Package Low Noise: 30VRMS (10Hz to 100kHz) Low Quiescent Current: 30A Low Dropout Voltage: 340mV Output Current: 200mA Fixed Output Voltage: -5V Adjustable Output from -1.22V to - 20V Positive or Negative Shutdown Logic 3A Quiescent Current in Shutdown Stable with 1F Output Capacitor Stable with Aluminum, Tantalum, or Ceramic Capacitors Thermal Limiting
The LT(R)1964 is a micropower low noise low dropout negative regulator. The device is capable of supplying 200mA of output current with a dropout voltage of 340mV. Low quiescent current (30A operating and 3A shutdown) makes the LT1964 an excellent choice for batterypowered applications. Quiescent current is well controlled in dropout. Other features of the LT1964 include low output noise. With the addition of an external 0.01F bypass capacitor, output noise is reduced to 30VRMS over a 10Hz to 100kHz bandwidth. The LT1964 is capable of operating with small capacitors and is stable with output capacitors as low as 1F. Small ceramic capacitors can be used without the necessary addition of ESR as is common with other regulators. Internal protection circuitry includes reverse output protection, current limiting, and thermal limiting. The device is available with a fixed output voltage of -5V and as an adjustable device with a -1.22V reference voltage. The LT1964 regulators are available in the a low profile (1mm) ThinSOT package.
, LTC and LT are registered trademarks of Linear Technology Corporation. ThinSOT is a trademark of Linear Technology Corporation.
APPLICATIO S
s s s
s
Low Current Regulator Regulator for Battery-Powered Systems Low Noise Regulator for Noise-Sensitive Instrumentation Negative Complement to LT1761 Family of Positive LDOs
TYPICAL APPLICATIO
10Hz to 100kHz Output Noise -5V Low Noise Regulator
1F VIN -5.4V TO -20V 10F BYP 0.01F VOUT 100V/DIV 30VRMS
GND SHDN
LT1964-5 IN OUT
-5V AT 200mA 30VRMS NOISE
1964 TA01a
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
U
1ms/DIV
1964 TA01b
U
U
1
LT1964
ABSOLUTE
AXI U RATI GS (Note 1)
SHDN Pin Voltage (with Respect to GND Pin) ........................ -20V, 15V Output Short-Circuit Duration .......................... Indefinite Operating Junction Temperature Range (Note 10) ............................... - 40C to 125C Storage Temperature Range ................. - 65C to 150C Lead Temperature (Soldering, 10 sec).................. 300C
IN Pin Voltage ........................................................ 20V OUT Pin Voltage (Note 11) .................................... 20V OUT to IN Differential Voltage (Note 11) ....... -0.5V, 20V ADJ Pin Voltage (with Respect to IN Pin) (Note 11) ........... -0.5V, 20V BYP Pin Voltage (with Respect to IN Pin) ................................... 20V SHDN Pin Voltage (with Respect to IN Pin) (Note 11) ........... -0.5V, 35V
PACKAGE/ORDER I FOR ATIO
TOP VIEW GND 1 IN 2 SHDN 3 4 ADJ 5 OUT
ORDER PART NUMBER LT1964ES5-SD S5 PART MARKING LTVX ORDER PART NUMBER LT1964ES5-BYP S5 PART MARKING LTVY
GND 1 IN 2 BYP 3 4 SHDN TOP VIEW 5 OUT
S5 PACKAGE 5-LEAD PLASTIC SOT-23
TJMAX = 125C, JA = 250C/W SEE THE APPLICATIONS INFORMATION SECTION
TOP VIEW GND 1 IN 2 BYP 3 4 ADJ 5 OUT
S5 PACKAGE 5-LEAD PLASTIC SOT-23
TJMAX = 125C, JA = 250C/W SEE THE APPLICATIONS INFORMATION SECTION
Consult LTC Marketing for parts specified with wider operating temperature ranges.
The q denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C.
PARAMETER Regulated Output Voltage (Notes 3, 9) ADJ Pin Voltage (Notes 2, 3, 9) Line Regulation Load Regulation CONDITIONS LT1964-5 LT1964 LT1964-5 LT1964 (Note 2) LT1964-5 LT1964 VIN = -5.5V, I LOAD = - 1mA -20V < VIN < -6V, -200mA < ILOAD < -1mA VIN = -2V, I LOAD = - 1mA -20V < VIN < -2.8V, -200mA < ILOAD < -1mA VIN = -5.5V to -20V, I LOAD = - 1mA VIN = -2.8V to -20V, I LOAD = - 1mA VIN = -6V, I LOAD = - 1mA to -200mA VIN = -6V, I LOAD = - 1mA to -200mA VIN = -2.8V, I LOAD = - 1mA to -200mA VIN = -2.8V, I LOAD = - 1mA to -200mA
q q q q q
ELECTRICAL CHARACTERISTICS
2
U
U
W
WW U
W
ORDER PART NUMBER LT1964ES5-5 S5 PART MARKING LTVZ
S5 PACKAGE 5-LEAD PLASTIC SOT-23
TJMAX = 125C, JA = 250C/W SEE THE APPLICATIONS INFORMATION SECTION
MIN -4.925 -4.850 -1.202 -1.184
TYP -5 -5 -1.22 -1.22 15 1 15 2
MAX -5.075 -5.150 -1.238 -1.256 50 12 35 50 7 15
UNITS V V V V mV mV mV mV mV mV
q
LT1964
The q denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C.
PARAMETER Dropout Voltage VIN = VOUT(NOMINAL) (Notes 4, 5) CONDITIONS I LOAD = - 1mA I LOAD = - 1mA I LOAD = - 10mA I LOAD = - 10mA I LOAD = - 100mA I LOAD = - 100mA I LOAD = - 200mA I LOAD = - 200mA GND Pin Current VIN = VOUT(NOMINAL) (Notes 4, 6) I LOAD = 0mA I LOAD = - 1mA I LOAD = - 10mA I LOAD = - 100mA I LOAD = - 200mA COUT = 10F, CBYP = 0.01F, ILOAD = -200mA, BW = 10Hz to 100kHz (Notes 2, 7) LT1964-BYP LT1964-SD VOUT = Off to On (Positive) VOUT = Off to On (Negative) VOUT = On to Off (Positive) VOUT = On to Off (Negative) VSHDN = 0V VSHDN = 15V VSHDN = -15V VIN = -6V, VSHDN = 0V VIN - VOUT = -1.5V(Avg), VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = -200mA VIN = -6V, VOUT = 0V VIN = VOUT(NOMINAL) -1.5V, VOUT = 0.1V VIN = 20V, VOUT, VADJ, VSHDN = Open Circuit
q q q q q q q q q q
ELECTRICAL CHARACTERISTICS
MIN
TYP 0.1 0.15
MAX 0.15 0.19 0.20 0.25 0.33 0.39 0.42 0.49 70 180 600 3 6 100 -2.8 -2.2 2.1 -2.8
UNITS V V V V V V V V A A A mA mA VRMS nA V V V V V V A A A A dB mA mA
q
0.26
q
0.34
q q q q q q
30 85 300 1.3 2.5 30 30 -1.8 -1.6 1.6 -2.1 0.8 -0.8 0.1 6 -3 3 46 54 350 220
Output Voltage Noise ADJ Pin Bias Current Minimum Input Voltage (Note 12) ILOAD = -200mA Shutdown Threshold
0.25 -0.25 -1
SHDN Pin Current (Note 8)
1 15 -9 10
Quiescent Current in Shutdown Ripple Rejection Current Limit Input Reverse Leakage Current
1
mA
Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: The LT1964 (adjustable version) is tested and specified for these conditions with the ADJ pin connected to the OUT pin. Note 3: Operating conditions are limited by maximum junction temperature. The regulated output voltage specification will not apply for all possible combinations of input voltage and output current. When operating at maximum input voltage, the output current range must be limited. When operating at maximum output current, the input voltage range must be limited. Note 4: To satisfy requirements for minimum input voltage, the LT1964 (adjustable version) is tested and specified for these conditions with an external resistor divider (two 249k resistors) for an output voltage of -2.44V. The external resistor divider will add a 5A DC load on the output. Note 5: Dropout voltage is the minimum input to output voltage differential needed to maintain regulation at a specified output current. In dropout, the output voltage will be equal to: (VIN + VDROPOUT). Note 6: GND pin current is tested with VIN = VOUT(NOMINAL) and a current source load. This means the device is tested while operating in its dropout
region. This is the worst-case GND pin current. The GND pin current will decrease slightly at higher input voltages. Note 7: ADJ pin bias current flows out of the ADJ pin. Note 8: Positive SHDN pin current flows into the SHDN pin. SHDN pin current is included in the GND pin current specification. Note 9: For input-to-output differential voltages greater than 7V, a 50A load is needed to maintain regulation. Note 10: The LT1964E is guaranteed to meet performance specifications from 0C to 125C. Specifications over the -40C to 125C operating temperature range are assured by design, characterization and correlation with statistical process controls. Note 11: A parasitic diode exists internally on the LT1964 between this pin and the IN pin. This pin cannot be pulled more than 0.5V more negative than the IN pin during fault conditions, and must remain at a voltage more positive than the IN pin during operation. Note 12: For the LT1964-BYP, this specification accounts for the operating threshold of the SHDN pin, which is tied to the IN pin internally. For the LT1964-SD, the SHDN threshold must be met to ensure device operation.
3
LT1964
PI FU CTIO S
GND (Pin 1): Ground. IN (Pin 2): Power is Supplied to the Device Through the Input Pin. A bypass capacitor is required on this pin if the device is more than six inches away from the main input filter capacitor. In general, the output impedance of a battery rises with frequency, so it is advisable to include a bypass capacitor in battery-powered circuits. A bypass capacitor in the range of 1F to 10F is sufficient. BYP (Pin 3, Fixed/-BYP devices): The BYP Pin is used to Bypass the Reference of the LT1964 to Achieve Low Noise Performance from the Regulator. A small capacitor from the output to this pin will bypass the reference to lower the output voltage noise. A maximum value of 0.01F can be used for reducing output voltage noise to a typical 30VRMS over a 10Hz to 100kHz bandwidth. If not used, this pin must be left unconnected. SHDN (Pin 3/4, -SHDN/Fixed Devices): The SHDN Pin is used to put the LT1964 into a Low Power Shutdown State. The SHDN pin is referenced to the GND pin for regulator control, allowing the LT1964 to be driven by either positive or negative logic. The output of the LT1964 will be off when the SHDN pin is pulled within 0.8V of GND. Pulling the SHDN pin more than -2.1V or +1.6V will turn the LT1964 on. The SHDN pin can be driven by 5V logic or open collector logic with a pullup resistor. The pullup resistor is required to supply the pullup current of the open collector gate, normally several microamperes, and the SHDN pin current, typically 3A out of the pin (for negative logic) or 6A into the pin (for positive logic). If unused, the SHDN pin must be connected to VIN. The device will be shut down if the SHDN pin is open circuit. For the LT1964-BYP, the SHDN pin is internally connected to VIN. A parasitic diode exists between the SHDN pin and the input of the LT1964. The SHDN pin cannot be pulled more negative than the input during normal operation, or more than 0.5V below the input during a fault condition. ADJ (Pin 4, Adjustable Devices only): For the Adjustable LT1964, this is the Input to the Error Amplifier. The ADJ pin has a bias current of 30nA that flows out of the pin. The ADJ pin voltage is -1.22V referenced to ground, and the output voltage range is -1.22V to -20V. A parasitic diode exists between the ADJ pin and the input of the LT1964. The ADJ pin cannot be pulled more negative than the input during normal operation, or more than 0.5V below the input during a fault condition. OUT (Pin 5): The Output Supplies Power to the Load. A minimum output capacitor of 1F is required to prevent oscillations. Larger output capacitors will be required for applications with large transient loads to limit peak voltage transients. A parasitic diode exists between the output and the input. The output cannot be pulled more negative than the input during normal operation, or more than 0.5V below the input during a fault condition. See the Applications Information section for more information on output capacitance and reverse output characteristics.
APPLICATIO S I FOR ATIO
The LT1964 is a 200mA negative low dropout regulator with micropower quiescent current and shutdown. The device is capable of supplying 200mA at a dropout voltage of 340mV. Output voltage noise can be lowered to 30VRMS over a 10Hz to 100kHz bandwidth with the addition of a 0.01F reference bypass capacitor. Additionally, the reference bypass capacitor will improve transient response of the regulator, lowering the settling time for transient load conditions. The low operating quiescent current (30A) drops to 3A in shutdown. In addition to the low quiescent current, the LT1964 incorporates several protection
4
U
W
U
U
U
U
U
features which make it ideal for use in battery-powered systems. In dual supply applications where the regulator load is returned to a positive supply, the output can be pulled above ground by as much as 20V and still allow the device to start and operate. Adjustable Operation The adjustable version of the LT1964 has an output voltage range of -1.22V to -20V. The output voltage is set by the ratio of two external resistors as shown in Figure 1. The device servos the output to maintain the voltage at the
LT1964
APPLICATIO S I FOR ATIO
ADJ pin at -1.22V referenced to ground. The current in R1 is then equal to -1.22V/R1 and the current in R2 is the current in R1 plus the ADJ pin bias current. The ADJ pin bias current, 30nA at 25C, flows through R2 out of the ADJ pin. The output voltage can be calculated using the formula in Figure 1. The value of R1 should be less than 250k to minimize errors in the output voltage caused by the ADJ pin bias current. Note that in shutdown the output is turned off and the divider current will be zero. The adjustable device is tested and specified with the ADJ pin tied to the OUT pin and a 5A DC load (unless otherwise specified) for an output voltage of -1.22V. Specifications for output voltages greater than -1.22V will be proportional to the ratio of the desired output voltage to -1.22V; (VOUT/-1.22V). For example, load regulation for an output current change of 1mA to 200mA is 2mV typical at VOUT = -1.22V. At VOUT = -12V, load regulation is: (-12V/-1.22V) * (2mV) = 19.6mV
R1 GND VIN ADJ LT1964 IN OUT R2
+
VOUT
1964 F01
VOUT = -1.22V(1 + R2 ) - (IADJ)(R2) R1 VADJ = -1.22V IADJ = 30nA AT 25C OUTPUT RANGE = -1.22V TO -20V
Figure 1. Adjustable Operation
Bypass Capacitance and Low Noise Performance The LT1964 may be used with the addition of a bypass capacitor from VOUT to the BYP pin to lower output voltage noise. A good quality low leakage capacitor is recommended. This capacitor will bypass the reference of the LT1964, providing a low frequency noise pole. The noise pole provided by this bypass capacitor will lower the output voltage noise to as low as 30VRMS with the addition of a 0.01F bypass capacitor. Using a bypass capacitor has the added benefit of improving transient response. However, regulator start-up time is inversely proportional to the size of the bypass capacitor.
U
Higher values of output voltage noise may be measured if care is not exercised with regard to circuit layout and testing. Crosstalk from nearby traces can induce unwanted noise onto the output of the LT1964-X. Output Capacitance and Transient Response The LT1964 is designed to be stable with a wide range of output capacitors. The ESR of the output capacitor affects stability, most notably with small capacitors. A minimum output capacitor of 1F with an ESR of 3 or less is recommended to prevent oscillations. The LT1964 is a micropower device and output transient response will be a function of output capacitance. Larger values of output capacitance decrease the peak deviations and provide improved transient response for larger load current changes. Bypass capacitors, used to decouple individual components powered by the LT1964, will increase the effective output capacitor value. Extra consideration must be given to the use of ceramic capacitors. Ceramic capacitors are manufactured with a variety of dielectrics, each with different behavior across temperature and applied voltage. The most common dielectrics used are Z5U, Y5V, X5R, and X7R. The Z5U and Y5V dielectrics are good for providing high capacitances in a small package, but exhibit strong voltage and temperature coefficients as shown in Figures 2 and 3. When used with a -5V regulator, a 10F Y5V capacitor can exhibit an effective value as low as 1F to 2F over the operating temperature range. The X5R and X7R dielectrics result in more stable characteristics and are more suitable for use as the output capacitor. The X7R type has better stability across temperature, while the X5R is less expensive and is available in higher values. Voltage and temperature coefficients are not the only sources of problems. Some ceramic capacitors have a piezoelectric response. A piezoelectric device generates voltage across its terminals due to mechanical stress, similar to the way a piezoelectric accelerometer or microphone works. For a ceramic capacitor the stress can be induced by vibrations in the system or thermal transients. The resulting voltages produced can cause appreciable amounts of noise, especially when a ceramic capacitor is used for noise bypassing. A ceramic capacitor produced
W
U
U
5
LT1964
APPLICATIO S I FOR ATIO
Figure 4's trace in response to light tapping from a pencil. Similar vibration induced behavior can masquerade as increased output voltage noise.
20 0 BOTH CAPACITORS ARE 16V, 1210 CASE SIZE, 10F X5R -20 -40 -60 Y5V -80 -100
CHANGE IN VALUE (%)
0
2
4
8 6 10 12 DC BIAS VOLTAGE (V)
14
16
1964 F02
Figure 2. Ceramic Capacitor DC Bias Characteristics
40 20
CHANGE IN VALUE (%)
0 -20 -40 -60 -80 BOTH CAPACITORS ARE 16V, 1210 CASE SIZE, 10F 50 25 75 0 TEMPERATURE (C) Y5V
X5R
-100 -50 -25
100
125
1964 F03
Figure 3. Ceramic Capacitor Temperature Characteristics
VOUT 1mV/DIV
LT1964-5 100ms/DIV COUT = 10F CBYP = 0.01F ILOAD = -200mA
1964 F04
Figure 4. Noise Resulting from Tapping on a Ceramic Capacitor
6
U
Thermal Considerations The power handling capability of the device will be limited by the maximum rated junction temperature (125C). The power dissipated by the device will be made up of two components: 1. Output current multiplied by the input/output voltage differential: IOUT * (VIN - VOUT), and 2. Ground pin current multiplied by the input voltage: IGND * VIN. The GND pin current can be found by examining the GND Pin Current curves in the Typical Performance Characteristics. Power dissipation will be equal to the sum of the two components listed above. The LT1964 series regulators have internal thermal limiting designed to protect the device during overload conditions. For continuous normal conditions the maximum junction temperature rating of 125C must not be exceeded. It is important to give careful consideration to all sources of thermal resistance from junction to ambient. Additional heat sources mounted nearby must also be considered. For surface mount devices, heat sinking is accomplished by using the heat spreading capabilities of the PC board and its copper traces. Copper board stiffeners and plated through-holes can also be used to spread the heat generated by power devices. The following table lists thermal resistance for several different board sizes and copper areas. All measurements were taken in still air on 3/32" FR-4 board with one ounce copper.
Table 1. Measured Thermal Resistance
COPPER AREA TOPSIDE* BACKSIDE 2500mm2 1000mm2 225mm2 100mm2 50mm2 2500mm2 2500mm2 2500mm2 2500mm2 2500mm2 BOARD AREA 2500mm2 2500mm2 2500mm2 2500mm2 2500mm2 THERMAL RESISTANCE (JUNCTION-TO-AMBIENT) 125C/W 125C/W 130C/W 135C/W 150C/W *Device is mounted on topside.
W
U
U
LT1964
APPLICATIO S I FOR ATIO
Calculating Junction Temperature
Example: Given an output voltage of -5V, an input voltage range of -6V to -8V, an output current range of 0mA to -100mA, and a maximum ambient temperature of 50C, what will the maximum junction temperature be? The power dissipated by the device will be equal to: IOUT(MAX) * (VIN(MAX) - VOUT) + (IGND * VIN(MAX)) where, IOUT(MAX) = -100mA VIN(MAX) = -8V IGND at (IOUT = -100mA, VIN = -8V) = -2mA so, P = -100mA * (-8V + 5V) + (-2mA * -8V) = 0.32W The thermal resistance will be in the range of 125C/W to 150C/W depending on the copper area. So the junction temperature rise above ambient will be approximately equal to: 0.32W * 140C/W = 44.2C The maximum junction temperature will then be equal to the maximum junction temperature rise above ambient plus the maximum ambient temperature or: TJMAX = 50C + 44.2C = 94.2C Protection Features The LT1964 incorporates several protection features which make it ideal for use in battery-powered circuits. In addition to the normal protection features associated with monolithic regulators, such as current limiting and thermal limiting, the device is protected against reverse input voltages and reverse output voltages. Current limit protection and thermal overload protection are intended to protect the device against current overload conditions at the output of the device. For normal operation, the junction temperature should not exceed 125C. The output of the LT1964 can be pulled above ground without damaging the device. If the input is left open circuit
U
or grounded, the output can be pulled above ground by 20V. For fixed voltage versions, the output will act like a large resistor, typically 500k or higher, limiting current flow to less than 40A. For adjustable versions, the output will act like an open circuit, no current will flow into the pin. If the input is powered by a voltage source, the output will sink the short-circuit current of the device and will protect itself by thermal limiting. In this case, grounding the SHDN pin will turn off the device and stop the output from sinking the short-circuit current. Like many IC power regulators, the LT1964 series have safe operating area protection. The safe area protection activates at input-to-output differential voltages greater than -7V. The safe area protection decreases the current limit as the input-to-output differential voltage increases and keeps the power transistor inside a safe operating region for all values of forward input to-output voltage. The protection is designed to provide some output current at all values of input-to-output voltage up to the device breakdown. A 50A load is required at input-to-output differential voltages greater than -7V. When power is first turned on, as the input voltage rises, the output follows the input, allowing the regulator to start up into very heavy loads. During start-up, as the input voltage is rising, the input-to-output voltage differential is small, allowing the regulator to supply large output currents. With a high input voltage, a problem can occur wherein removal of an output short will not allow the output voltage to fully recover. Other regulators, such as the LT1175, also exhibit this phenomenon, so it is not unique to the LT1964 series. The problem occurs with a heavy output load when the input voltage is high and the output voltage is low. Common situations are immediately after the removal of a short-circuit or when the SHDN pin is pulled high after the input voltage has already been turned on. The load line for such a load may intersect the output current curve at two points. If this happens, there are two stable operating points for the regulator. With this double intersection, the input supply may need to be cycled down to zero and brought up again to make the output recover.
W
U
U
7
LT1964
PACKAGE DESCRIPTIO
A A1 A2 L
SOT-23 (Original) .90 - 1.45 (.035 - .057) .00 - .15 (.00 - .006) .90 - 1.30 (.035 - .051) .35 - .55 (.014 - .021)
SOT-23 (ThinSOT) 1.00 MAX (.039 MAX) .01 - .10 (.0004 - .004) .80 - .90 (.031 - .035) .30 - .50 REF (.012 - .019 REF) PIN ONE .95 (.037) REF .25 - .50 (.010 - .020) (5PLCS, NOTE 2) 2.60 - 3.00 (.102 - .118) 1.50 - 1.75 (.059 - .069) (NOTE 3)
.20 (.008) DATUM `A' A A2
L NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS MILLIMETERS 2. DIMENSIONS ARE IN (INCHES)
3. DRAWING NOT TO SCALE 4. DIMENSIONS ARE INCLUSIVE OF PLATING 5. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR 6. MOLD FLASH SHALL NOT EXCEED .254mm 7. PACKAGE EIAJ REFERENCE IS: SC-74A (EIAJ) FOR ORIGINAL JEDEC MO-193 FOR THIN
RELATED PARTS
PART NUMBER LT1120 LT1121 LT1129 LT1175 LT1611 LT1761 Series LT1762 Series LT1763 Series LT1764 LT1962 LT1963 DESCRIPTION 125mA Low Dropout Regulator with 20A IQ 150mA Micropower Low Dropout Regulator 700mA Micropower Low Dropout Regulator 500mA Negative Low Dropout Micropower Regulator Inverting 1.4MHz Switching Regulator in 5-Lead SOT-23 100mA, Low Noise, Low Dropout Micropower Regulators in SOT-23 150mA, Low Noise, LDO Micropower Regulators 500mA, Low Noise, LDO Micropower Regulators 3A, Low Noise, Fast Transient Response LDO 300mA, Low Noise, LDO Micropower Regulators 1.5A, Low Noise, Fast Transient Response LDO COMMENTS Includes 2.5V Reference and Comparator 30A IQ, SOT-223 Package 50A Quiescent Current 45A IQ, 0.26V Dropout Voltage, SOT-223 Package -5V at 150mA from 5V Input, Tiny SOT-23 Package 20V Quiescent Current, 20VRMS Noise, SOT-23 Package 25A Quiescent Current, 20VRMS Noise, MSOP Package 30A Quiescent Current, 20VRMS Noise, SO-8 Package 40VRMS, 5-Lead DD Package -5V at 350mA from 5V Input, Tiny SOT-23 Package 30A Quiescent Current, 20VRMS Noise, MSOP Package 40VRMS Noise, SOT-223 Package
LT1931/LT1931A Inverting 1.2MHz/2.2MHz Switching Regulator in 5-Lead SOT-23
8
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 q FAX: (408) 434-0507
q
U
S5 Package 5-Lead Plastic SOT-23
(Reference LTC DWG # 05-08-1633) (Reference LTC DWG # 05-08-1635)
2.80 - 3.10 (.110 - .118) (NOTE 3) .09 - .20 (.004 - .008) (NOTE 2) 1.90 (.074) REF A1
S5 SOT-23 0401
1964i LT/TP 1001 1.5K * PRINTED IN USA
www.linear.com
(c) LINEAR TECHNOLOGY CORPORATION 2001

▲Up To Search▲

Price & Availability of LT1964

	To Download LT1964 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .